Spektrum Dx8

[AlexBooo]

Sembra interessante, sperando che non hanno introdotto nuovi bug. Chi fa da cavia?

Certo se le corse vanno a donnine allegre è na bella rottura...

[BBC25185]

Originalmente inviato da AlexBooo

Sembra interessante, sperando che non hanno introdotto nuovi bug. Chi fa da cavia?

Certo se le corse vanno a donnine allegre è na bella rottura...

Sicuramente, appena ne avrò la possibilità, lo metto!!!

[m.rik]

Originalmente inviato da egicar

È disponibile AirWare 2.05 😊

Version 2.05
10 August 2012

Software Features

• Added support for GPS and High Current telemetry sensors.
• Enabled up to 32-pole motors for the brushless RPM sensor.
• Enabled SD telemetry log file
• Enabled ability to configure inactivity timer
• Enabled backlight configurability (Auto/On/Off)
• Enabled dimming control of the orange Spektrum LED for night flying
• Adjusted vibe motor RPM to be less aggressive
Software Corrections
• Fixed bug that could reset the radio when scrolling through Mix options.
• Corrected L/R trimmer ‘forgetting’ assignment after power cycle.
• Improved translations in French and Italian screens.
• Corrected export of flap configuration.
• Corrected over-travel of flaps that could result in reversed operation at extreme deployments.
• Corrected switch change on Acro throttle cut screen when going from the initial switch selection to the edit page.
• Corrected timer to work properly in Throttle Out mode when using reversed throttle channel.
• Corrected end-point adjustability when Trainer is used as an input to a channel.
• Corrected trainer normal Master mode so that it doesn’t modify controls from the
slave. In previous versions it could reverse channels vs. what was expected.
NOTE: This change affects sub-trim and travel of existing models and ones you will import. You may need to adjust sub-trims and travel on all control surfaces in both airplanes and helicopters.

Ciao
Egidio

volevo già farlo per altre tue precedenti segnalazioni / link.
Lo faccio ora:
Grazie Egidio.

Con quest'ultima però, quando l'ho ricevuta sul telefonino, ho piantato tutto e tutti e quando sono finalmente tornato a casa per scaricarla ed installarla sono rimasto a bocca asciutta.
La prossima volta, scrivi "coming soon", e non "è disponibile".

Ciao

[AEROX_15]

Ancora niente purtroppo, e siamo al 12 agosto...
Siamo sicuri sia veramente disponibile?

[double68]

Pazientiamo in religioso silenzio... 😔

[AEROX_15]

Originalmente inviato da double68

Pazientiamo in religioso silenzio... 😔

L'attesa si fa sentire!!

[AlexBooo]

Che esagerati, che è st'attesa spasmodica...

[AEROX_15]

Originalmente inviato da AlexBooo

Che esagerati, che è st'attesa spasmodica...

vogliamo l'upgrade !!!!!!!!

[BBC25185]

Originalmente inviato da AEROX_15

vogliamo l'upgrade !!!!!!!!

Inviato dal mio GT-I9100 con Tapatalk 2

[AEROX_15]

Originalmente inviato da egicar

È disponibile AirWare 2.05 😊

Version 2.05
10 August 2012

Software Features

• Added support for GPS and High Current telemetry sensors.
• Enabled up to 32-pole motors for the brushless RPM sensor.
• Enabled SD telemetry log file
• Enabled ability to configure inactivity timer
• Enabled backlight configurability (Auto/On/Off)
• Enabled dimming control of the orange Spektrum LED for night flying
• Adjusted vibe motor RPM to be less aggressive
Software Corrections
• Fixed bug that could reset the radio when scrolling through Mix options.
• Corrected L/R trimmer ‘forgetting’ assignment after power cycle.
• Improved translations in French and Italian screens.
• Corrected export of flap configuration.
• Corrected over-travel of flaps that could result in reversed operation at extreme deployments.
• Corrected switch change on Acro throttle cut screen when going from the initial switch selection to the edit page.
• Corrected timer to work properly in Throttle Out mode when using reversed throttle channel.
• Corrected end-point adjustability when Trainer is used as an input to a channel.
• Corrected trainer normal Master mode so that it doesn’t modify controls from the
slave. In previous versions it could reverse channels vs. what was expected.
NOTE: This change affects sub-trim and travel of existing models and ones you will import. You may need to adjust sub-trims and travel on all control surfaces in both airplanes and helicopters.

Ciao
Egidio

Egidio dove hai trovato questa notizia ??

ci stanno facendo aspettare un po troppo con questo upgrade Non vorrei mai che sia tutto una bufala