12 luglio 07, 19:21 | #1 (permalink) Top |
User Data registr.: 16-06-2006 Residenza: Milano
Messaggi: 260
| hirobo shuttle: dove mettere il gyro?
Ciao a tutti, ieri ho preso un hirobo shuttle plus 2, oggi l'ho montato ma ho un dubbio: sul raptor, sullo style, sul trex metto il giroscopio dietro, sull'hirobo, dove lo posiziono? davanti sopra batterie e ricevente? mi sembra un po instabile a metterlo li.... grazie a tutti per i consigli...
|
13 luglio 07, 09:57 | #5 (permalink) Top |
User |
Si il manuale dice di metterlo li, ma ad un amico abbiamo fatto una modifica limando il piano dietro al piatto, dove di solito si mettono i gyro e posizionato li. Sotto al ciclico dietro al motore si imbratta di unto. Comunque in teoria il posto migliore e' proprio dove lo mette lo shuttle.
__________________ "Donne e Rotori, gioie e dolori" |
14 luglio 07, 08:22 | #8 (permalink) Top |
User Data registr.: 25-04-2005 Residenza: Milano
Messaggi: 660
|
la velocità angolare è costante; i motivi sono altri: se lo metti vicino al ruotino aumenti l'inerzia della coda, inoltre vicino al centro di rotazione delle pale è piu' sicuro che all' estremità. all'interno del telaio è ancora piu' protetto. guarda JK dove mette il 401 sul trex se. |
14 luglio 07, 09:17 | #9 (permalink) Top |
User Data registr.: 24-05-2007
Messaggi: 118
|
Mounting the gyro This is one of the most important considerations if the full potential of the SL720 is to be realised. The gyro must be mounted on a horizontal surface. This surface must be accurately at right angles to the main shaft of the helicopter in both pitch and roll directions. Failure to do this will cause unwanted rollyaw or pitch-yaw interactions. Although the SMM gyro sensor has a high degree of shock and vibration immunity the SL720 performs best if sited at a point of low vibration in the helicopter airframe. Where possible a location close to the centre of gravity of the helicopter is advantageous. Especially avoid siting the gyro at the extreme front of the radio tray as this area is subject to high levels of main rotor generated vibration and flexing of the tray under servo loads will be transmitted to the gyro. Generally the gyro will more accurately track the motion of the helicopter if mounted at the rear of the frames. Poor location of the sensor can impose a wobbling motion on the sensor from the main rotor or the engine and produce a vibrationally induced precession of the heading (see Appendix J for more information). Mount the gyro so that the LEDs can easily be seen. Queste sono le istruzioni dedl csm720, a mio avviso il miglior gyro, il problema non è la velocità angolare ma l'amplificazione delle vibrazioni. ciao |
Bookmarks |
| |
Discussioni simili | ||||
Discussione | Autore discussione | Forum | Commenti | Ultimo Commento |
aiuto, non so piu dove mettere sta guarnizione | taggiascoz | Automodellismo | 6 | 20 febbraio 06 08:03 |
Hirobo shuttle zxx os 32 oppure Hirobo plus 36? | abellodenonna | Elimodellismo in Generale | 1 | 23 dicembre 05 17:05 |
dove mettere i video? | skylyne74 | Modellismo | 2 | 10 novembre 05 16:41 |
Hirobo Shuttle Plus | garbo | Elimodellismo in Generale | 3 | 03 maggio 05 12:04 |